Like with anything else, with age comes weariness. If that’s the case for humans, then it can also be applied for material things as well. Take door locks for example, they tend to spur up a few problems as time progresses. We’ll tell you now, that if you haven’t encountered any problems yet with your door lock, then you’re surely going to in the future.
In times like these, it’s best that you have a speed-dial for a 24 hour locksmith service to assist you in fixing or installing a new set of locks. Luckily, companies like Keyside Locksmiths are available to fill in your requests any time of the day for the whole week. However, for you to have knowledge on whether it’s time to fix your lock or not, we’re going to show you some common problems for door locks that are severe enough to warrant a locksmith call.
1. A Broken Key in Your Lock
Losing a key to your lock is one thing, but breaking one is just as bad. In fact, it can be really troublesome if the key breaks inside the locking mechanism because of the difficulty in getting it out, and depending how deep it is inside, it could lead to the mechanism getting stuck, or worse getting broken. It makes an already difficult job even harder to do.
One thing to take note of is if you’re not experienced, you should never attempt to pull it off on your own because you might just end up breaking the whole lock instead. This goes even if you have your key extraction set. Your best bet would be to hire a professional locksmith to do the job for you. It’ll cost you, but what’s worse, paying for the service, or for a new lock installation?
2. Jammed Locks
Having a jammed lock is another thing you shouldn’t ignore early on. Locks get stuck for a number of reasons, one being because of a build-up of dirt, debris, or foreign contaminants inside of the lock. If you can, try cleaning the inside away with regular cleaning tools, but this might involve dismantling the lock itself because of those hard-to-reach areas inside. Then, you’ll have to apply a lubricant that is the designated one for your lock.
It’s important you know what type of product you’ll be using because you might just end up damaging it further if you use the wrong one. The most common lubricant homeowners use is WD-40, but that doesn’t mean that it can be used for all.
3. Misaligned Door Locks
Aside from the fact that it’s a sight for sore eyes to look at, misaligned door locks are no laughing matter. To put it in simplest terms, having misaligned locks means that the locking bolt is not in line with the striking plate. When left untreated, the condition will worsen overtime every time someone closes the door, possibly leading to the lock breaking. The most common causes are usually due to bad installation and/or door degradation due to the climate.
To fix, you’ll need to reinstall the lock striking plate again so that it properly aligns with the bolt. This involves unscrewing it from its original position and adjusting it to the optimal height. To save you the trouble, however, make sure that the hinges of your door are aligned, because it might just be that that’s causing the problem and it’ll save you the time and effort if you were to fix the locking mechanism itself.
4. Loose Door Locks
Although less serious than other door problems, it’s still worth taking note of. Think of it this way, if a machine needs all its parts to work properly, imagine removing one of them from it. Same goes for locks, if one of the moving parts inside the locking mechanism becomes loose, then the whole lock could possibly break entirely. Extended use of the lock usually results in this type of problem, and the usual fix for it is just to tighten everything from bottom up. If it’s too used to put back, then it might be the right time to get a replacement. Take note however, if there’s still a problem occurring after all that, then it could be because there’s a bigger problem hiding inside.
5. Lock Cylinder Won’t Open the Door
The normal scenario when opening your door is that you should be able to open when you place your key inside the lock cylinder, the problem lies when you notice that it’s the entire cylinder that’s turning. This usually means that there is a problem with the screws inside the locking mechanism, it could be loose or damaged.
To fix this, it requires you to open the lock and fix the screws inside holding the cylinder in place. Doing this though depends on the kind of lock you have installed, because the process could vary for different locks. If you somehow locate the screws inside and they’re still in good condition, tighten them up and if you remove the faceplate for the lock back to where it originally was. Otherwise, you may need to replace the screws already.